Comments on: HC-06 Bluetooth module datasheet and configuration with Arduino https://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino/ Hobby robotics and electronics with Arduino, ESP82666 and Raspberry Pi Fri, 11 Sep 2020 07:26:27 +0000 hourly 1 https://wordpress.org/?v=5.6.11 By: 用Arduino Uno重置HC-06蓝牙模块？ – FIXBBS https://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino/#comment-354996 Fri, 11 Sep 2020 07:26:27 +0000 http://42bots.com/?p=1033#comment-354996 […] http://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino/ […]

]]> By: blackbee https://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino/#comment-288425 Tue, 12 Mar 2019 03:58:38 +0000 http://42bots.com/?p=1033#comment-288425 Hello, what if I type “AT” and there is no response? Is the Bluetooth HC06 is not working or receiving any data?

]]> By: Mohammad https://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino/#comment-281891 Mon, 10 Dec 2018 18:14:38 +0000 http://42bots.com/?p=1033#comment-281891 hello everybody.
i have two questions i hope someone could help me:
first, are name, pin code and baud rate set on hc-06 when it is bought?? and when you connect vcc and ground, you should be able to search and find, and pair it???
i mean is it possible these elements be empty??
and the second question:
recently i bought hc-06, and after some days try i could get access to Bluetooth module through AT commands.
But because none of my devices could find the hc-06 Bluetooth module i tried other AT commands to check what the problem is.
AT+PO (which changes the parity) was the command which caused i lost access to AT commands.
could anyone help me to take it back to none parity?
by the way: sorry for lack of English and i am beginner in working by Arduino Uno
Thanks a lot

]]> By: Problem mit hc-06 bluetooth modul? – HKTXT https://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino/#comment-269027 Wed, 29 Aug 2018 22:07:16 +0000 http://42bots.com/?p=1033#comment-269027 […] HC-06 Bluetooth module datasheet and configuration … […]

]]> By: Sam Wong https://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino/#comment-240934 Fri, 26 Jan 2018 03:46:40 +0000 http://42bots.com/?p=1033#comment-240934 Problem of entering AT command mode
I connected my new HC-06(4 terminal points) to the Arduino UNO exactly as the diagram shown above and successfully uploaded the sketch. However, I didn’t get a response after entering “AT” via the serial monitor. I tried different baud rate and “no line ending, new line, both NL & CR” but none of them worked. I checked the connection numerous times and could not find a mismatch. The only thing I found is that my HC-06 does not have a “key” but replaced by a “EN”. Is this the culprit of my failure?
Remark: I believe my HC-06 is physically sound as it could communicate quite well with my mobile phone via “Bluetooth Terminal” yesterday.
Thanks.

]]> By: Manny https://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino/#comment-208942 Sun, 07 May 2017 06:31:41 +0000 http://42bots.com/?p=1033#comment-208942 Hello,

I have followed your instructions with success!

For my case, within the Arduino IDE serial monitor, I simply had to choose “No line ending” and I managed to upgrade the baud rate to 115200.

Thank you very much for your very helpful post:-)
Manny

]]> By: HC-06 and AT-09 BLE module with the Arduino | smartmecard https://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino/#comment-204663 Sun, 12 Mar 2017 04:59:54 +0000 http://42bots.com/?p=1033#comment-204663 […] 2. HC-06 Bluetooth module datasheet and configuration with Arduino http://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino […]

]]> By: Daniel Fernandes https://42bots.com/tutorials/hc-06-bluetooth-module-datasheet-and-configuration-with-arduino/#comment-189135 Sat, 10 Sep 2016 17:38:59 +0000 http://42bots.com/?p=1033#comment-189135 Hello Friends! Already I tried everything but I can not!
I received the message “Type AT commands” but when I type the command, do not receive return; If anyone can help me, thank you

]]>